Single Pane Glass Repair in an Aluminum Frame, Part 2
This week we are going to continue our series on single pane window glass repair. Let's talk about broken glass in a fixed window, usually referred to as a picture window. The most common type will have metal stops on the outside, around all four edges of the window glass. Sometimes these stops will be held in place with screws, and other times there will be aluminum stops that snap in place. In some rare instances there will be a rubber material in place of metal. If you have the screw type, you remove all of the screws and each piece will come out. If you have the metal snap in stops, carefully pry the stop from the frame using a small, flat screwdriver or a putty knife. You want to start in a corner and work along the stop until it comes out. Don't pry too much because the stops can bend very easily. If you have the rubber type, pry a corner away using the screwdriver, grab it with your fingers, and pull out the rubber. The glass shouldn't fall out because there is a glue or tape on the edge, holding the glass in place.
From here, You can get your measurements for the new piece of glass. The glass edges will be exposed, and you can hook your tape measure to the edge and get your width and height. If there is a hole in the glass, measure the glass thickness. If there isn't a hole, put on some gloves and carefully push on the glass where the crack is located. This will expose the edge so you can measure it. When you go to get the new glass, you're going to need a tube of silicone to replace the glue or tape holding the glass in place. Once you get the glass home, you need to remove the old glass. Go inside and cut between the glass and frame using a utility knife with a new blade. This will cut away the silicone or tape that is holding the old glass. Be sure to wear heavy gloves during this process to avoid getting cut. Start at the top and cut across from one corner to the other. Then cut down one side, from top to bottom. Do the other side the same way. At this point the glass should fall out. You should place a tarp or sheet under the window to catch the glass as it falls out. Using a stiff putty knife, scrape off the old silicone or tape from the frame. If there were setting blocks on the bottom, be sure to reuse them. They act as shims to raise the glass off the bottom.
Now run a bead of silicone about 3/16" thick around the perimeter of the opening. Grab your new glass on the sides, angle the bottom in and the top out, set the glass on the setting blocks, then slowly raise the glass up into place. Push just hard enough that all four edges of the glass contact the silicone, but not so hard that the glass makes contact with the metal frame. Install your outside stops. Don't clean the glass for 24 hours so the silicone can set up.
Next week I will continue this series on window glass repair.
John Rocco has been installing
replacement windows since 1978. To learn more, visit How To Install Windows
 Continue for more related information:
|
| RELATED RESULTS: |
|
| |
Color Help: Color Theory and Design Psychology
Color theory is an entire science unto itself, and to get a full picture of how it all works, I'd suggest picking up a ... Save Time & Money Doing Your Own Basic Electric Wiring
Hiring a professional electrician can be very expensive and is often the reason why people try doing their own... Kitchen Remodeling Guide
A kitchen can make or ruin a family life. A badly designed, ill-equipped and cluttered kitchen is likely to affect the peace of mind of an o... Strongly Scented Candles: Use your mouth, nose and eyes to tell
Triple scented, heavily scented, strongly scented - these are all phrases candle manufacturers are us... How to Modify Your Landscaping to Protect Your House from Burglars
Believe it or not, landscaping can be an important part of a good home security plan. A burglar wh... Are Showers Harmful to Your Health?
The last thing you would think about when you are taking a nice, refreshing shower is, "Am I jeopardizing my health"?
... Home Office: Identifying Your Needs
Not many years ago, the thought of working from home wasconsidered a fantastic vision of the distant future. However,with more and... What is Injection Waterproofing?
Injection waterproofing is often used to fill and seal cracks and crevices. The material is most often made from a polyurethane comp... Key Bathroom Remodeling Ideas
One of the simplest ways to start planning your bathroom remodeling is to tour other bathrooms to get bathroom remodeling ideas. Pay at... Log Homes for Beginners - 10 Steps to Success
For those who may be thinking of building a new log home and enjoying the lifestyle that comes with it, there are a num... |
|