Repairing a Hole in a Sheetrocked Wall






It is quite simple to repair a hole in a Sheetrocked wall, however there are minor differences in methods of repair depending on how large the hole is.



Small size holes (1/4" or smaller)

With small holes, simply apply a little joint compound or wall putty with a small putty knife or trowel. Let dry, then sand lightly and paint.

Medium size holes (Greater than ¼" in diameter and smaller than 2" in diameter)

First clean out the hole and surrounding area of any debris and loose sheetrock. Then apply a mesh tape, specifically manufactured for sheetrock applications, across the hole. Use your putty knife to ensure that it is applied evenly on the wall surface. Next apply a liberal amount of Joint Compound over the hole and mesh. Let this set for 1 to 2 days.

After the initial coat has been applied and has had time to fully dry, apply a second skim coat of Joint Compound over the area. However, this time spread the Joint Compound over an area that is 2-3 times the size of the original hole. Basically you want to flare out the area that you are repairing so that it will blend in nicely with the rest of the wall. Again let the area dry for a day.

Finally lightly sand the area and apply one last skim coat over the area. Again spreading the Joint Compound out a little further than the last application. Let the Joint Compound set up one more day, sand lightly and then paint.

Holes larger than 2 inches

With large holes, I recommend cutting out an area such that a new small piece of sheetrock can be applied to the 2"x4" studs. For example, I would consider putting in a new 16"x16" piece of sheetrock for a hole that is greater than 2" in diameter and less than 16" in diameter.

The best method to remove the piece of damage sheetrock is to use a Carpenters knife (razor blade) and score the area where you want to cut out. Repeatedly apply the knife until you have worked your way through the sheetrock. When complete, you should have about ½" to ¾" of the 2"x4" stud showing on each of the two exposed studs.

Note: Care should be taken to ensure no wires are cut behind the sheetrock when cutting out the damaged piece.

Next, cut a piece of new sheetrock to the size of the hole, and secure with sheetrock screws or ringed sheetrock nails.

Next, tape the cracks with the mesh tape material mentioned above. Then as described earlier, apply three skim coats of Joint Compound, with each successive coat getting flared out further. Make sure you wait for the Joint Compound to dry before applying the next coat. Perform a final light sand after the final coat has been applied and has had time to dry, and then paint.

About the Author:
me_donovan@comcast.net
http://www.homeadditionplus.com
 http://www.homeaddition.blogspot.com


Over the past 20+ years Mr. Donovan has been involved with building homes and additions to homes. His projects have included: building a vacation home, building additions and garages on to existing homes, and finishing unfinished homes. Mr. Donovan's formal education and profession have been as an Electrical Engineer and Marketing Manager.

 Continue for more related information:
RELATED RESULTS:


 

Is It Time For Solar Energy to Get Hot?
Solar energy has been around for quite a while and most people don't think about it much except for the ones who are already ...

Basement Waterproofing Advice
Basements need to be waterproofed for many reasons. Cracks in the walls, leaking windows and pipe condensation are probably the most co...

Used But Not Used Up
Some DIY Maintence will put Used tools back in Main Stream Operation: ...

Reviewing and Evaluating Laminate Floors
Since the introduction of laminate flooring into the US in 1982, the sector has experienced growth of up to 20% per annum at...

10 Spring Cleaning Tips For Your Kitchen
The words "spring cleaning" can make the neatest person cringe. They mean more work. As if cleaning all year long wasn't eno...

Bathroom Magic
Believe it or not, the bathroom is one of the most magickal rooms in your house; Your make up box and medicine chest can be treasure chest of tools , ...

Fire Hazard Alert - Is Your Dryer Ready to Ignite
In recent years there has been many stories about dryers catching on fire. Should we be concerned? Yes of course. W...

Installing Vinyl Siding - Making It Simple
Installing vinyl siding can be a very rewarding process that could dramatically change the appearance of your home. For the...

Wallpaper Doesnt Just Cover...It Defines The Room
Wallpaper is often overlooked as a key part of an attractive home. The right wallpaper will add character to any ro...

Why You Should Get A Patio Awning
In these days of climate change, the UK summer is believe or not, getting warmer and sunnier. Whilst this gives us opportunity to en...
Table of Contents | Article-Max Directory